Section XV: Base metals and articles of base metal
Chapter 72: Iron and steel
29 headings. Open one to see every Sri Lankan tariff line under it with the duty, taxes and requirements. Search all codes
- 72.01Pig iron and, Spiegeleisen in pigs, blocks or other primary forms3 lines
- 72.02Ferro-alloys15 lines
- 72.03Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99.94%, in lumps, pellets or similar forms2 lines
- 72.04Ferrous waste and scrap; remelting scrap ingots of iron or steel7 lines
- 72.05Granules and powders, of pig iron, spiegeleisen, iron or steel3 lines
- 72.06Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 72.03)2 lines
- 72.07Semi-finished products of iron or non- alloy steel7 lines
- 72.08Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot- rolled, not clad, plated or coated14 lines
- 72.09Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold rolled (cold-reduced), not clad, plated or coated9 lines
- 72.10Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated17 lines
- 72.11Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated6 lines
- 72.12Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated9 lines
- 72.13Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel6 lines
- 72.14Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling9 lines
- 72.15Other bars and rods of iron or non-alloy steel3 lines
- 72.16Angles, shapes and sections of iron or non-alloy steel11 lines
- 72.17Wire of iron or non-alloy steel7 lines
- 72.18Stainless steel in ingots or other primary forms; semi-finished products of stainless steel3 lines
- 72.19Flat-rolled products of stainless steel, of a width of 600 mm or more14 lines
- 72.20Flat-rolled products of stainless steel, of a width of less than 600 mm4 lines
- 72.21Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel1 line
- 72.22Other bars and rods of stainless steel; angles, shapes and sections of stainless steel5 lines
- 72.23Wire of stainless steel1 line
- 72.24Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel2 lines
- 72.25Flat-rolled products of other alloy steel, of a width of 600 mm or more8 lines
- 72.26Flat-rolled products of other alloy steel, of a width of less than 600 mm6 lines
- 72.27Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel3 lines
- 72.28Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel8 lines
- 72.29Wire of other alloy steel2 lines
Chapter notes (legal text)
The notes decide what belongs in this chapter and what does not. Read them when two codes seem to fit.
Notes.
1. In this Chapter and, in the case of Notes (d), (e) and (f) throughout the Nomenclature, the following expressions have the meanings hereby assigned to them :
(a) Pig iron
Iron-carbon alloys not usefully malleable, containing more than 2 % by weight of carbon and which may contain by weight one or more other elements within the
following limits :
- not more than 10 % of chromium
- not more than 6 % of manganese
- not more than 3 % of phosphorus
- not more than 8 % of silicon
- a total of not more than 10 % of other elements
(b) Spiegeleisen
Iron-carbon alloys containing by weight more than 6 % but not more than 30 % of manganese and otherwise conforming to the specification at (a) above.
(c) Ferro-alloys
Alloys in pigs, blocks, lumps or similar primary forms, in forms obtained by continuous casting and also in granular or powder forms, whether or not
agglomerated, commonly used as an additive in the manufacture of other alloys or as de-oxidants, de-sulphurising agents or for similar uses in ferrous metallurgy and generally not usefully malleable, containing by weight 4 %
or more of the element iron and one or more of the following :
- more than 10 % of chromium
- more than 30 % of manganese
- more than 3 % of phosphorus
- more than 8 % of silicon
- a total of more than 10 % of other elements, excluding carbon, subject to a maximum content of 10 % in the case of copper.
(d) Steel
Ferrous materials other than those of heading 72.03 which (with the exception of certain types produced in the form of castings) are usefully malleable and
which contain by weight 2 % or less of carbon.
However, chromium steels may contain higher proportions of carbon.
(e) Stainless steel
Alloy steels containing, by weight, 1.2 % or less of carbon and 10.5 % or more of chromium, with or without other elements.
(f) Other alloy steel
Steels not complying with the definition of stainless steel and containing by weight one or more of the following elements in the proportion shown :
- 0.3 % or more of aluminium
- 0.0008 % or more of boron
- 0.3 % or more of chromium
- 0.3 % or more of cobalt
- 0.4 % or more of copper
- 0.4 % or more of lead
- 1.65 % or more of manganese
- 0.08 % or more of molybdenum
- 0.3 % or more of nickel
- 0.06 % or more of niobium
- 0.6 % or more of silicon
- 0.05 % or more of titanium
- 0.3 % or more of tungsten (wolfram)
- 0.1 % or more of vanadium
- 0.05 % or more of zirconium
- 0.1 % or more of other elements (except sulphur, phosphorus, carbon and nitrogen), taken separately.
Section XV - Chapter 72 - Page 1
(g) Remelting scrap ingots of iron or steel
Products roughly cast in the form of ingots without feeder-heads or hot tops, or of pigs, having obvious surface faults and not complying with the chemical composition of pig iron, spiegeleisen or ferro-alloys.
(h) Granules
Products of which less than 90 % by weight passes through a sieve with a mesh aperture of 1 mm and of which 90 % or more by weight passes through a sieve with a mesh aperture of 5mm.
(ij) Semi-finished products
Continuous cast products of solid section, whether or not subjected to primary hot-rolling; and
Other products of solid section, which have not been further worked than subjected to primary hotrolling or roughly shaped by forging, including blanks for angles,
shapes or sections.
These products are not presented in coils.
(k) Flat-rolled products
Rolled products of solid rectangular (other than square) cross-section, which do not conform to the definition at (ij) above in the form of :
- coils of successively superimposed layers, or
- straight lengths, which if of a thickness less than 4.75 mm are of a width measuring at least ten times the thickness or if of a thickness of 4.75 mm or more are of
a width which exceeds 150 mm and measures at least twice the thickness.
Flat-rolled products include those with patterns in relief derived directly from rolling (for example, grooves, ribs, chequers, tears, buttons, lozenges) and those which
have been perforated, corrugated or polished, provided that they do not there by assume the character of articles or products of other headings.
Flat-rolled products of a shape other than rectangular or square, of any size, are to be classified as products of a width of 600 mm or more, provided that they do
not assume the character of articles or products of other headings.
(l) Bars and rods, hot-rolled, in irregularly wound coils
Hot-rolled products in irregularly wound coils, which have a solid cross-section in the shape of circles, segments of circles, ovals, rectangles (including squares),
triangles or other convex polygons (including “flattened circles” and “modified rectangles”, of which two opposite sides are convex arcs, the other two sides being
straight, of equal length and parallel). These products may have indentations, ribs, grooves or other deformations produced during the rolling process (reinforcing bars and rods).
Section XV - Chapter 72 - Page 2
(m) Other bars and rods
Products which do not conform to any of the definitions at (ij), (k) or (l) above or to the definition of wire, which have a uniform solid cross-section along their
whole length in the shape of circles, segments of circles, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and
“modified rectangles”, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). These products may :
- have indentations, ribs, grooves or other deformations produced during the rolling process(reinforcing bars and rods);
- be twisted after rolling.
(n) Angles, shapes and sections
Products having a uniform solid cross-section along their whole length which do not conform to any of the definitions at (ij), (k), (l) or (m) above or to the definition
of wire.
Chapter 72 does not include products of heading 73.01 or 73.02.
(o) Wire
Cold-formed products in coils, of any uniform solid cross-section along their whole length, which do not conform to the definition of flat-rolled products.
(p) Hollow drill bars and rods
Hollow bars and rods of any cross-section, suitable for drills, of which the greatest external dimension of the cross-section exceeds 15 mm but does not exceed 52 mm, and of which the greatest internal dimension does not
exceed one half of the greatest external dimension. Hollow bars and rods of iron or steel not conforming to this definition are to be classified in heading 73.04.
2.- Ferrous metals clad with another ferrous metal are to be classified as products of the ferrous metal predominating by weight.
3.- Iron or steel products obtained by electrolytic deposition, by pressure casting or by sintering are to be classified, according to their form, their composition and their appearance, in the headings of this Chapter appropriate to similar hot-rolled
products.
Subheading Notes.
1.- In this Chapter the following expressions have the meanings hereby assigned to them :
(a) Alloy pig iron
Pig iron containing, by weight, one or more of the following elements in the specified proportions :
- more than 0.2 % of chromium
- more than 0.3 % of copper
- more than 0.3 % of nickel
- more than 0.1 % of any of the following elements : aluminium, molybdenum, titanium, ungsten (wolfram), vanadium.
(b) Non-alloy free-cutting steel
Non-alloy steel containing, by weight, one or more of the following elements in the specified proportions :
- 0.08 % or more of sulphur
- 0.1 % or more of lead
- more than 0.05 % of selenium
- more than 0.01 % of tellurium
- more than 0.05 % of bismuth.
(c) Silicon-electrical steel
Alloy steels containing by weight at least 0.6 % but not more than 6 % of silicon and not more than 0.08 % of carbon. They may also contain by weight not more than
1 % of aluminium but no other element in a proportion that would give the steel the characteristics of another alloy steel.
(d) High speed steel
Alloy steels containing, with or without other elements, at least two of the three elements molybdenum, tungsten and vanadium with a combined content by weight of
7 % or more, 0.6 % or more of carbon and 3 to 6 % of chromium.
(e) Silico-manganese steel
Alloy steels containing by weight :
Section XV - Chapter 72 - Page 3
Alloy steels containing by weight :
- not more than 0.7 % of carbon,
- 0.5 % or more but not more than 1.9 % of manganese, and
- 0.6 % or more but not more than 2.3 % of silicon, but no other element in a proportion that would give the steel the characteristics of another alloy steel.
2.- For the classification of ferro-alloys in the subheadings of heading 72.02 the following rule should be observed :
A ferro-alloy is considered as binary and classified under the relevant subheading (if it exists) if only one of the alloy elements exceeds the minimum percentage laid down
in Chapter Note 1 (c); by analogy, it is considered respectively as ternary or quaternary if two or three alloy elements exceed the minimum percentage.
